Frequently Asked Questions

Help & Support

Frequently Asked Questions

Find answers to common questions about TYPETRO shocks, complete strut assemblies, installation guides, service life, and troubleshooting.

Product Basics

3 Questions
What is included in a TYPETRO complete strut assembly?

Each assembly arrives fully built and ready to install. It includes the strut mount, mount bushing, bearing, bump stop, dust boot, coil spring, spring seat, lower isolator and a brand-new strut.

Strut mount Designed to reduce noise and vibration.
Bump stop Helps control rebound motion.
Dust boot Shields the piston rod and oil seal from damage.
Coil spring Matched to OE specifications and powder coated for a longer service life.
Piston rod Polished with a chrome finish for added durability.
Precision valving Delivers consistent, confident ride control.
Hydraulic oil Performs across a wide temperature range for a steady ride.
Strut Built for your specific vehicle to restore like-new handling.
How does a shock absorber work?

Inside every shock absorber is a piston that pushes oil through very small openings as it moves. Because only a small amount of fluid can pass through at a time, the piston is slowed down. This slows, or "damps", the movement of the spring and suspension.

What is the difference between a shock absorber and a strut?

Shocks and struts do a similar job but are built very differently. Both control excess spring movement. A strut, however, is also a structural part of the suspension.

A single strut can replace two or three conventional suspension components. It often acts as a pivot point for steering and helps set wheel position during alignment.

Installation

2 Questions
How do I install a complete strut assembly?

A complete strut assembly is quick and straightforward to fit, and no spring compressor is needed. Follow these general steps, and always refer to your vehicle owner manual for exact procedures and torque specifications.

1
Remove the wheel
Lift the vehicle with a jack and place a jack stand at the lift point shown in your owner manual. Remove the wheel bolts, then take off the wheel and tire.
2
Remove the old strut
Undo the nuts at the knuckle and the sway bar link, then separate the strut from the knuckle. Remove the upper mounting bolts and lift the strut out of the vehicle.
3
Compare old and new
Before fitting the new assembly, set it next to the old one. Check the strut mount holes, spring seat insulator and sway bar link holes, and confirm their positions match. Any mismatch can prevent a proper fit.
4
Fit the new strut
Guide the new assembly into place and line everything up without forcing it. Raise the knuckle to seat the strut, then refit every nut and tighten to the manufacturer torque specification.
Note: If you are not comfortable with the work, have a qualified technician install it.
Does my vehicle need an alignment after replacing struts?

Yes. We recommend a wheel alignment after replacing struts or doing any major front suspension work. Removing and refitting a strut directly affects camber and caster, which can change your alignment settings.

Wear & Replacement

4 Questions
How many miles do shocks and struts last?

Experts generally recommend replacing shocks and struts at around 50,000 miles. Testing shows that original gas-charged units wear measurably by that point, and replacing them often improves handling and comfort.

Unlike a tire, which turns a fixed number of times per mile, a shock or strut may cycle several times per mile on smooth roads and hundreds of times per mile on rough ones. Service life is also affected by climate, road contaminants, driving habits, vehicle load, tire and wheel changes, and the overall condition of the suspension.

Have your shocks and struts inspected by a dealer or an ASE-certified technician once a year, or every 12,000 miles.

Note: Actual mileage varies with driving style, vehicle type and road conditions.
How do I know when my shocks or struts need replacing?

Tires, brakes and wipers are easy to check. Shocks and struts are not, even though they are safety-critical and wear down with everyday driving. Have them inspected whenever your vehicle is in for tire, brake or alignment service.

Warning signs include unusual suspension noise, excessive bounce or sway, and nose-dive when braking. A shock or strut should also be repaired or replaced if it has lost a large amount of fluid, is bent or broken, or has damaged brackets or worn bushings.

Replacement is generally needed when a part no longer does its job, no longer meets its design specification, or is missing. You may also choose to upgrade to improve ride quality, as a preventive measure, or for a special need, such as load-assist shocks for a vehicle that regularly carries extra weight.

What happens if I do not replace worn shocks or struts?

Shocks and struts are an essential part of your suspension. They protect other suspension components and your tires from premature wear. When they wear out, your ability to brake, steer and stay stable can suffer.

They also keep your tires in contact with the road and reduce how quickly weight shifts between the wheels during cornering and braking.

My new tires are wearing unevenly. Could the ride control parts be the cause?

Five factors directly affect tire wear:

1 Driving habits
2 Alignment settings
3 Tire pressure
4 Worn suspension or steering components
5 Worn shocks or struts
Note: A cupped wear pattern usually points to worn steering or suspension parts, or worn shocks and struts. Worn ball joints, control arm bushings or wheel bearings tend to cause irregular cupping, while worn shocks and struts typically leave a repeating pattern. Inspect every part before replacing it so you do not swap out components that are still good.

Troubleshooting

4 Questions
There is a light film of oil on my shock or strut. Should I replace it?

Not if it is working properly. A light film of oil over the upper half of the working chamber is normal. It forms when lubricating oil is wiped off the rod as it moves into the painted section of the unit.

Manufacturers add a little extra oil to compensate for this. Fluid running down the side of the unit, however, indicates a worn or damaged seal, and the unit should be replaced.

I have replaced my shocks or struts several times in a few months because of oil leaks. Why do they keep failing?

The most common cause of leaks is seal damage, so the underlying cause should be found and fixed before you replace the unit again.

Most suspensions use rubber jounce and rebound bumpers to protect the shock or strut from topping out or bottoming out. Most struts also have a replaceable dust boot that keeps dirt away from the oil seals. If these parts are worn, cracked, damaged or missing, replace them to help your new shocks or struts last longer.

I was told my strut is leaking oil, but it is gas-charged. Is that possible?

Yes. Gas-charged shocks and struts contain the same amount of oil as standard hydraulic units. The gas pressure is added to prevent shock fade, which happens when oil foams from agitation, heat and low-pressure areas behind the piston.

The pressure compresses trapped air bubbles until they are too small to affect performance, giving a smoother and more consistent ride.

I replaced my shocks or struts but still hear a metallic clunk over bumps. Are the new parts faulty?

Most likely not. A metallic clunk usually points to loose or worn mounting hardware.

For shocks, check that all mounts are tight and look for other worn suspension parts. Clevis-style mounts must clamp the shock sleeve firmly, much like a vise, to stay quiet. For struts, inspect the upper bearing plate and replace it if needed.

Old mounting bolts can stretch if they were over-torqued or tightened and loosened many times. If a bolt no longer holds its torque or has stretched, replace it.

Air Suspension

2 Questions
Should I replace my air suspension parts or switch to a coil spring conversion kit?

If you value load leveling or towing capability, we recommend replacing the air suspension components and keeping the original system.

If you are tired of replacing air suspension parts one after another, a coil spring conversion kit is a dependable and far more economical alternative.

My air suspension has failed. Should I repair it or replace it?

When an air suspension can no longer hold air, repairs can be expensive, and OE parts may no longer be available for older vehicles. Remanufactured or new aftermarket electronic air struts and compressors are a cost-effective way to keep the full air ride experience.

The other option is a conversion kit that replaces the air system with conventional steel coil springs and standard struts or shocks. It greatly reduces the risk of air spring failure and restores your correct ride height.

Still have questions?

Need vehicle fitment verification, part number matching, or technical suspension assistance? Our engineering support team is here to help.